40" FENN MODEL VNC 40 TUBE DRAWING/SPINNER BLOCK (11431)

MACHINE #11431

SPECIFICATIONS

-MANUFACTURER: FENN MANUFACTURING (SPX PRECISION COMPONENTS)

-MODEL: VNC 40

-TYPE: TUBE DRAWING/SPINNER BLOCK W/CARROUSEL CONVEYOR

-CAPACITY: 6,000 LBS PULL AT 550 FPM

-PREVIOUS USE: STEP REDUCTION- COPPER TUBE
-START SIZE: .750" (19mm) DIA X .041" (1.24mm) WALL

-DRAW SIZES: .633" (16.1mm) DIA X .034" (.86mm) WALL
.528" (13.4mm) DIA X .028" (.71mm) WALL
.437" (11.1mm) DIA X .024" (.61mm) WALL
.357" (9.1mm) DIA X .020" (.51mm) WALL
.288" (7.3mm) DIA X .018" (.46mm) WALL
.195" (4.9mm) DIA X .018" (.46mm) WALL
.136" (3.5mm) DIA X .018" (.46mm) WALL
.100" (2.5mm) DIA X .018" (.46mm) WALL
.076" (1.9mm) DIA X .018" (.46mm) WALL

-SPEED RANGE: 0/550/2250 FPM (0/167/685mpm)

-BLOCK DIAMETER: 40" (1016mm)

-DRIVE MOTOR INFO
-MAIN DRIVE MOTOR: 100 HP (74.57Kw) 500/2000 RPM
500 VOLT
-TAKE UP DRIVE MOTOR: 20 HP (14.9Kw) 1750 RPM DC
230 VOLT

-PAYOFF DRIVE MOTOR: 20 HP (14.9Kw) 1750 RPM DC
230 VOLT

-MAIN GEARBOX: 17" CRS (SPECIAL) WORM GEAR RIGHT ANGLE REDUCER
RATIO: 9.8/1

-HYDRAULICS
-MANUFACTURER: RACINE
-MODEL: 947648
-CAPACITY: 100 GALLONS
-MAX PRESSURE: 750 PSI
-MOTOR: 15 HP (11.2Kw) 1165 RPM AC
230/460 VOLT 3 PHASE 60 HERTZ
-PUMP: RACINE MODEL PVF PNTO 12ER 01
NOTE: HYDRAULIC POWER UNIT IS EQUIPPED WITH A HEAT EXCHANGER.

-
-TYPE: 8 STATION (BASKET) HYDRAULICALLY OPERATED
CARROUSEL

-BASKET/ COIL SIZE: 57" (1447.8mm) O.D. X 34" (863.6mm) I.D. X
21" (533.4mm) FACE WIDTH

INSTALLATION CONSISTS OF:

-INLET PAYOFF UNIT: THIS PAYOFF IS USED TO FEED THE STARTING SIZE
COIL OF TUBING

-MAXIMUM COIL O.D.: 80" (2032mm)
-COIL I.D.: 18"/24" (457/610mm) (MANUALLY ADJUSTED)
-FACE WIDTH: 10" (254mm)

-GUIDE BILLY ROLL: 3 1/2" (88.9mm) DIA 18 1/2" (469.9mm) FACE WIDTH
-PINCH ROLL GUIDE UNIT USED TO PULL THE TUBE OF THE INLET PAYOFF AND
FEED/GUIDE IT TO THE DIE AREA

-PINCH ROLLS
-QTY: 2 PAIR- ONE(1) ROLL OF EACH PAIR IS DRIVEN
-ROLL SIZE: 6 1/2" (165.1mm) O.D. X 1 5/8" (41.3mm) FACE
WIDTH

-DRIVE MOTOR FOR FEED UP: 2 HP (1.49Kw) 1725 RPM AC
208/230/460 VOLT 3 PHASE 60 HERTZ
-GEARBOX: WINSMITH SPEED REDUCER MODEL 11 HM
RATIO: 21.8/1

NOTE: UNIT IS EQUIPPED WITH AN AIR OPERATED 2 1/2"(63.5mm) DIA X 11 1/2"
(292.1mm) FACE WIDTH PRESSURE ROLL AT THE ENTRY SIDE TO HOLD THE TUBE IN
PLANE WITH THE PINCH ROLLS AND A 5 1/4"(131.3mm) DIA X 1 3/4"(44.5mm) FACE
WIDTH GUIDE ROLL AT THE EXIT SIDE. ROLL CLOSURE OF THE PINCH ROLLS IS
HYDRAULICALLY ACTUATED.

-DRIVEN INTEGRAL CARROUSEL
BASKET PAYOFF LOCATED BELOW FLOOR LEVEL, THIS UNIT LIFTS BASKET
UP TO MEET THE DIE BOX/STRAIGHTENER UNIT. ALLOWS
PAYOFF OF PREVIOUSLY DRAWN TUBING TO THE
DIE/STRAIGHTENER.

-DRIVE MOTOR: 20 HP (14.9Kw) 1750 RPM DC

NOTE: PAYOFF LIFT IS ACCOMPLISHED HYDRAULICALLY

-DIE BOX & STRAIGHTENER UNIT
-CONSISTS OF:

-BILLY ROLL: 3"(76.2) DIA X 11" (279.4mm) FACE WIDTH
-ENTRY GUIDE
-CASTER/STRAIGHTENER ROLLS
-QTY: 3
-(2)ADJUSTABLE SIMULTANEOUSLY ACROSS PASS
LINE VIA HAND CRANK
-(1)HYDRAULICALLY ACTUATED TO PINCH/ STRAIGHTEN
STOCK BEFORE ENTERING DIE

--ROLL SIZE: 5 1/4"(133.4mm) DIA X 1 3/4"(44.5mm) FACE WIDTH
ROLLS HAVE GENEROUS RADII ON FACE

-PIVOTING DIE BOX ASSY
-DIE SIZE: 3"(76.2mm) DIAMETER X 1 3/4"(44.5mm)

NOTE: DIE IS CONTINUOUSLY LUBED DURING OPERATION.

-INTEGRAL TUBE GRIPPER/DOG: MOUNTED ON THE DRAW BLOCK, THE GRIPPER GRABS THE
TUBE POINT AND HOLDS IT WHILE THE INITIAL WRAPS
ARE LAYERED UP THE BLOCK AS THE DIE BOX ASSY
RISES UP THE BLOCK MAINTAINING PROPER TUBE SPRING
TENSION (ALONG WITH SNUBBER ROLLS) UNTIL THE TUBE
IS CUT AT THE GRIPPER AREA ALLOWING THE TUBE TO
CASCADE CONTINUOUSLY INTO THE BASKET AS THE BLOCK
CONTINUES TO DRAW. tHE SNUBBER ROLLS CONTINUE TO
ASSIST IN ASSURING THE TUBE STAYS TIGHT ON THE
BLOCK DURING THE OPERATION.

NOTE: GRIPPER IS HYDRAULICALLY OPERATED TO EXTEND/RETRACT, OPEN/CLOSE, LOCK/
UNLOCK.

-SNUBBER ROLLS
-QTY: 3
-ROLL SIZE: 5 1/2"(139.7mm) X 11"(279.4mm) FACE WIDTH

NOTE: ROLLS ARE COATED WITH A URETHANE TYPE MATERIAL AND ALL ARE
HYDRAULICALLY ACTUATED TO ASSIST IN HOLDING TUBE ON BLOCK.

-POWERED TAKE UP AS WITH THE INTEGRAL PAYOFF THIS UNIT IS MOUNTED
BELOW FLOOR LEVEL AND RAISES TO ENGAGE THE
BASKET ON ITS LOCATING PIN. IT THEN RAISES THE
BASKET UP TO ALLOW THE LOCATING PIN IN THE BOTTOM
DRAW BLOCK TO ENGAGE THE TOP OF THE BASKET
SOLIDLY ORIENTING IT TO THE BLOCK FOR THE
DRAWING OPERATION. THE DRIVE MOTOR POWERS THE
ROTATION OF THE BASKET TO MATCH THE SPEED OF THE
BLOCK.

-DRIVE MOTOR: 20 HP (14.9Kw) 1750 RPM DC
230 VOLT

NOTE: TAKE UP LIFT IS HYDRAULICALLY ACTUATED

-LUBE UNIT SUPPLY LUBRICANT TO TUBE FOR DRAWING OPERATION
-CAPACITY: 45 GALLONS
-MAX PUMP DELIVERY: 6 GPM
-MOTOR: 3/4 (.56Kw) 1800 RPM AC

-ELECTRICS: DRIVES WERE UPGRADED IN A G.E. MODERNIZATION
PROGRAM IN 1988

-MANUFACTURER: GENERAL ELECTRIC
-DRIVE MODEL: DC-300 ADJUSTABLE SPEED DRIVE
GE FANUC SERIES SIX PLUS PROGRAMABLE CONTROLLER
W/NINE(9) GE GENIUS FANUC I/O BLOCKS

-DRIVE SPECS
-BLOCK DRIVE:
-S/N: PCOCS021CD02001
-INPUT VOLTAGE: 460
-INPUT AMPS: 137
-OUTPUT HP: 100
-OUTPUT VOLTAGE: 500
-OUTPUT AMPS: 166

-PAYOFF DRIVE:
-S/N: PCOCS021CD01001
-INPUT VOLTAGE: 230
-INPUT AMPS: 61
-OUTPUT HP: 20
-OUTPUT VOLTAGE: 240
-OUTPUT AMPS: 72

-TAKE UP DRIVE:
-S/N: PCOCS021CD03001
-INPUT VOLTAGE: 230
-INPUT AMPS: 61
-OUTPUT HP: 20
-OUTPUT VOLTAGE: 240
-OUTPUT AMPS: 72

-(2) TRANSFORMERS
-MANUFACTURER: GE
-TYPE: STEP DOWN
-MODEL: 9T23B3882
-CAPACITY: 30 KVA
-PRIMARY: 480 VOLTS
-SECONDARY: 230 VOLTS

-(1) TRANSFORMER
-MANUFACTURER: GE
-TYPE: ISOLATION
-MODEL: 9T48Y1084
-CAPACITY: 112.5 KVA
-HIGH: 480 VOLTS
-LOW: 480

ALL CONTROLS ARE INCLUDED ALONG SIX(6) VARIOUS OPERATOR STATIONS.

MACHINE IS DISMANTLED AND LYING IN STORAGE

**PRICE QUOTED IS EX-WORKS AS IS WHERE IS SUBJECT TO PRIOR SALE**

**ALL SPECIFICATIONS ARE SUBJECT TO VERIFICATION BY PURCHASER**