14" (355mm) x 3 1/4" (66.7mm) SECO DUAL GAUGE LOOP SLITTING LINE (7436)

SPECIFICATIONS

MANUFACTURER SECO

TYPE LOOP SLITTING LINE
-DUAL GAUGE: LINE IS EQUIPPED WITH
TWO SLITTER HEADS- ONE FOR LIGHT
GAUGE SLITTING AND ONE FOR HEAVIER
GAUGE SLITTING

GENERAL SPECIFICATIONS:

STRIP WIDTH
-MINIMUM 2" (51mm)
-MAXIMUM 14"(355mm)

SLIT WIDTH
-LIGHT GAUGE SLITTING HEAD .125" (3mm) TO 14" (355mm)
-HEAVY GAUGE SLITTING HEAD .375" (10mm) TO 14" (355mm)

MATERIAL GAUGE
-LIGHT GAUGE SLITTING HEAD .003" (.076mm) THICK TO .045" (1.143mm)THICK
-HEAVY GAUGE SLITTING HEAD .045" (1.143mm)THICK TO .204" (5.182mm)THICK

LINE SPEED 500 FEET PER MINUTE (152 mpm)

COIL
-SIZE RANGE
-INSIDE DIAMETER MINIMUM 16" (406mm) DIAMETER
-INSIDE DIAMETER MAXIMUM 20" (508mm) DIAMETER

-WEIGHT 6000 LBS (2727 kg)

LINE CONSISTS OF THE FOLLOWING:

(1) COIL CAR

-TYPE ABOVE GROUND-SIDE TRAVERSING

(1) COIL PAYOFF

-MANUFACTURER SECO

-CAPACITY 6,000 LBS (2727 kg)

-MANDREL
-SIZE MINIMUM- 16" (406mm) DIAMETER
MAXIMUM- 20" (508mm) DIAMETER
-EXPANSION TYPE HYDRAULIC

-DRIVE MOTOR 30 HP (22 kw) 500/2000 RPM DC

PAYOFF IS EQUIPPED WITH A SLIDING BASE.

(1) PEELER/HOLD DOWN ROLL UNIT

-MANUFACTURER SECO

-TYPE HYDRAULIC
DUAL CYLINDER

(1) SLITTER STAND

-MANUFACTURER SECO

-TYPE DRIVEN

-MANUFACTURER SECO

-DRIVE MOTOR 20 HP (15 kw) DC

SLITTER STAND IS EQUIPPED WITH A PAIR OF PINCH/HOLD DOWN ROLLS- ONE PAIR
BEFORE THE SLITTER HEAD AND ONE PAIR AFTER THE SLITTER HEAD TO MAINTAIN STOCK
TENSION AS IT PASSES THROUGH THE SLITTER HEAD. THESE PINCH ROLLS ARE AIR
OPERATED.

SLITTER STAND IS COMPLETE WITH TWO INTERCHANGEABLE SECO SLITTER HEADS:

-LIGHT GAUGE SLITTER HEAD

-MAXIMUM WIDTH 14" (355mm)
-ARBOR DIAMETER 3 1/4" (82.55mm)

-GAUGE RANGE
-MINIMUM .003" (.076mm)
-MAXIMUM .045" (1.143mm)

-HEAVY GAUGE SLITTER HEAD

-MAXIMUM WIDTH 14" (355mm)
-ARBOR DIAMETER 4 1/2" (114mm)

-GAUGE RANGE
-MINIMUM .045" (1.143mm)
-MAXIMUM .204" (5.182mm)

(1) SCRAP CHOPPER

(1) UPCOILER

-MANUFACTURER SECO

-ROLLS
-PINCH ROLLS 1 PAIR (2) LOCATED AT ENTRY
-FORMING ROLLS QUANTITY OF 3 TO TO UPCOIL MATERIAL

-ROLL DIAMETERS 6" (152mm)

-DRIVE MOTOR APPROXIMATELY 20 HP DC

UPCOILER IS EQUIPPED WITH A SLIDING BASE ALLOWING THE UNIT TO BE MOVED
COMPLETELY OUT IF THE MATERIAL LINE TO ALLOW MATERIAL TO BYPASS UNIT AND GO
DIRECTLY TO THE RECOILER.

(1) TENSION STAND

-MANUFACTURER SECO

-TYPE POWERED PINCH ROLLS

-DRIVE MOTOR 40 HP (30 kw) 875/1765 RPM DC

(1) RECOILER

-MANUFACTURER SECO

-CAPACITY 6,000 LBS (2727 kg)

-MANDREL SIZE RANGE
-MINIMUM 4" (102mm)
-MAXIMUM 20" (508mm)

-MANDREL EXPANSION TYPE MANUAL

-PUSHER PLATE HYDRAULICALLY OPERATED

-MAIN DRIVE MOTOR 60 HP (45 kw) 400/2000 RPM DC

RECOILER IS EQUIPPED WITH AN OVERARM SEPARATOR.

(1) DRIVE CONTROLS RELIANCE SCR DRIVE

PLEASE NOTE THAT GAUGES SHOWN IN QUOTE ARE BASED ON THE APPLICATION PREVIOUSLY
RUN ON THE LINE.

*******ALL SPECIFICATIONS SUBJECT TO VERIFICATION BY PURCHASER*******