TECHNICA GUSS MODEL 250 HORIZONTAL CONTINUOUS BRASS BILLET CASTING LINE (6645)

CONTINUOUS CASTER:
MANUFACTURER: TECHNICA GUSS
YEAR OF MANUFACTURE: 1974
MODEL NO.: 250 DR 111 SNE
STRAND DIAMETER: 2 x 8" DIAMETER OR 1 X 10" DIAMETER
2 X (203.2mm) DIAMETER OR 1 X 10" (254mm)
DIAMETER
HOLDING FURNACE CAPACITY: USAGE - 6200 KG
HEEL - 2000 KG

ELECTRICAL SPECIFICATIONS: 415 VOLT, 3 PHASE
TWO (2) INDUCTOR COILS
(TWO (2) SPARE COILS)
HOLDING FURNACE: 300 KW, 400 AMPS
THREE (3) FLYING SAWS (EACH): 22 KW, 93 AMPS
THREE (3) DRIVES (EACH): 11 KW, 54 AMPS TOTAL
ONE (1) HYDRAULIC TILT UNIT: 7.5 KW, 15 AMPS
THREE (3) FANS: 5.5 - 1.5 - 2.2 KW, 20 AMPS TOTAL

TOTAL CONNECTED LOAD: 580 AMPS

ONE (1) HOLDING FURNACE (3 STRANDS):
INCLUDING:
ONE (1) SPARE BODY (BARE)
ONE (1) SPARE INDUCTOR (READY)
TWO (2) SPARE COILS
THREE (3) SPARE FRONT PLATES (INCLUDING COOLERS)
ONE (1) SPARE W-CHANNEL MOLD

ONE (1) WITHDRAWAL UNIT (3 STRANDS):
INCLUDING:
ONE (1) SPARE GEAR BOX (READY)
TWO (2) SPARE HYDRAULIC DRIVES (READY)

THREE (3) FLYING SAWS:
INCLUDING:
ONE (1) SPARE UNIT (READY)

THREE (3) BILLET RUNWAYS

THREE (3) BILLET STILLAGES

INDUCTOR COILS:
1. SCOTT CONNECTED - BALANCED OVER 3 PHASES
2. SECONDARY VOLTAGE FROM 170 VOLTS TO 540 VOLTS IN 10 STEPS
(MANUALLY OPERATED VIA TAPPING SWITCH ON MAIN PANEL)

PROCESS CONTROLLER:
MANUFACTURER: SIEMENS SIMATIC
MODEL NO.: SS 115U
(SOME SPARES)

COOLING TOWER (INDUCED DRAFT):
MANUFACTURER: MULLER
YEAR OF MANUFACTURE: 1974
MODEL NO.: KTO 20 SP
WATER FLOW: 18 r/Sec. (65 m3/Hr.)
WATER IN: 54 DEGREES C.
WATER OUT: 28 DEGREES C.
WET BULB TEMPERATURE: 21 DEGREES C.
FAN: 15 KW
PUMP: 2000 LITERS
CIR. PUMPS: 2 x REGENT VERT. W LINE - 5.5 KW EACH
2 x REGENT VERT. W LINE - 22 KW EACH
TWO (2) PRIMING CHAMBERS, VALVES, PIPE WORK, FITTINGS AND CONNECTIONS

STANDBY PACKAGED GENERATING SET FOR EMERGENCY COOLING:
MANUFACTURER: GENERAC - OLYMPIAN
YEAR OF MANUFACTURE: 1997
MODEL NO.: CD080
ENGINE: CATERPILLAR
RATING: 80 KW
AUTOMATIC MONITORING OF COOLING TOWER
AUTO START IN CASE OF POWER FAILURE
AUTO SWITCHING TO GENERATOR
MANUAL RESET TO NET
PROCESS CONTROLLER: SIEMENS SIMATIC
MODEL NO.: S 7 214

TWO (2) CHANNEL INDUCTION FURNACES:
MANUFACTURER: BIRLEC
YEAR OF MANUFACTURE: 1973
RATING (MAX./MIN.): 600 KW - 530 KW
POURING CAPACITY: USABLE - 5000 KG
HEEL - 1700 KG
NO. OF INDUCTORS: TWO (2) - AIR COOLED
POWER CONSUMPTION: 240 KW / TON
MELTING RATE: 2.5 TONS/HR. @ 950 DEGREES C.
ELECTRICAL CONNECT: 415 VOLTS, 3 PHASE, 50 HERTZ

GENERAL EQUIPMENT:
- HYDRAULIC TILTING GEAR W/TWO (2) CYLINDERS CONNECTED TO HYDRAULIC POWER
PACK. LIMIT SWITCH CONTROL.
- INSTRUMENT (CONTROL) PANEL WITH OPERATOR CONTROL DESK.
- CONTRACTOR PANEL FOR MAIN & STANDBY CONTRACTORS.
- AIR CIRCUIT BREAKER FOR 3 PHASE, 415 VOLTS, 50 HERTZ SUPPLY.
- 720 KVA SCOTT CONNECTED TRANSFORMER GROUP.
- NATURALLY COOLED POWER FACTOR CORRECTION CAPACITORS.
- TWO (2) FANS INCLUDING DUCT WORK.
- FOUR (4) SPARE INDUCTORS - READY TO GO.
- TWO (2) TRANSFER LADLE PLATFORM SCALES (10,000 KG) INCLUDING DIGITAL
READOUTS, WALL MOUNTED SLAVE READOUTS (LARGE DIGITS) AND PRINTER.
- ALL NECESSARY EQUIPMENT & FORMERS FOR FURNACE BODY & INDUCTOR REBUILDING.

TWO (2) CHANNEL INDUCTION FURNACES (CONT'D):
MANUFACTURER: IN-HOUSE DESIGN
YEAR OF MANUFACTURE: 1961
RATING (MIN./MAX.): 176 KW (MAX. 330 KVA - NOMINAL 298 KVA)
POURING CAPACITY: USABLE - 1000 KG
HEEL - 600 KG
NO. OF INDUCTORS: ONE (1) - FAN COOLED
MELTING RATE: 1000 KG/HR.
ELECTRICAL CONNECT: 415 VOLTS, 3 PHASE, 50 HERTZ

GENERAL EQUIPMENT:
- HYDRAULIC TILTING GEAR W/TWO (2) CYLINDERS CONNECTED TO HYD. POWER PACK.
- INSTRUMENT (CONTROL) PANEL AND OPERATOR CONTROL DESK.
- TAPPING TRANSFORMER (AUTO).
- TWO (2) FANS INCLUDING DUCT WORK.
- ONE (1) STATIC BILLET MOLD CARROUSEL.
- 4 x 8 DEGREE MOLDS - 3 x 10 DEGREE MOLDS
- ALL NECESSARY EQUIPMENT & FORMERS FOR FURNACE BODY & INDUCTOR REBUILDING.

*********SPECIFICATIONS ARE SUBJECT TO BUYERS VERIFICATION*******************